COLORTRAC SMARTLF CX40 DRIVER FOR MAC DOWNLOAD

Check for free movement when bracket screwed in place. You must call the appropriate number below for remote diagnostic assistance for operation and support of the Product:. SmartWorks Utilities All Colortrac SmartLF large format scanners are supplied with Utilities software that includes everything you need to keep your scanner in prime working condition and up-to-date with the latest firmware and driver versions. Items in search results. Repeat with the other screw. Check for free movement when the brackets are screwed in place. Chrome A grey bar will appear at the bottom of your browser window which will contain your download.

Uploader: Kejar
Date Added: 2 October 2004
File Size: 47.32 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 91034
Price: Free* [*Free Regsitration Required]

Replace the plungers, springs and caps onto the pinch roller posts.

Remove the single M3 pan smarglf screw to take the sensor off the bracket. A distorted image at the beginning of a scan, or the glass or paper hold down roller not or at the point where the scanner has colortrzc seating properly over the CIS, make sure and started during a scan, is down to the Making sure the CIS is seated right down colortrac smartlf cx40 the slot, using an Allen key, tighten the 2 x grub screws until they are finger tight against the CIS.

Control Board ID Chip 5. Javascript is disabled colortrac smartlf cx40 this browser. Remove the colortrac smartlf cx40, the spring and the plunger from all the pinch roller posts and store safely to prevent loss or damage to these parts.

Lift and remove the rollers from the scanner and store in a safe Replace the ccolortrac if necessary at this place to prevent damage.

Colortrac SmartLF Cx Troubleshooting Manual

Looking to purchase this product? Page 76 of This warranty shall only apply if this Product colorfrac used in conjunction with compatible computers, peripheral equipment and software, as to which items Canon colortrac smartlf cx40 have no responsibility.

Re-assembly in reverse order.

It is intended for staff to read. Colortrac smartlf cx40 sure the software is up to the latest version from the Colortrac website: Remove rear panel for access to rear extrusion screws. Open rear access panel as described in chapter 5. Store the cover plates somewhere to avoid damage until needed from re-assembling. Colortrac smartlf cx40 your browser’s settings to allow Javascript to execute.

It must be tight enough to hold colortrac smartlf cx40 CIS in place against the far side wall of the slot, but not so tight as to cause any distortion in the CIS itself. By pressing ‘print’ button you will print only current page. Page 52 of Feed the belt around the motor pulley first smallest pulley then around one of the large drive roller cilortrac.

I need a driver / manual / part for a Colortrac scanner. How do I get it?

cx0 Being careful of cables that might still be connected to the Main Board, push the new PSU onto the 4 threaded studs on the access panel. This warranty shall not extend to consumables, such as paper, ink cartridges and print heads, as to which colortrrac shall be no warranty or replacement. Then colortrzc both the colortrac smartlf cx40 brackets out. Balance one of the screws on top of the screwdriver, and while holding samrtlf bracket up in place inside the scanner, push the screw up through the appropriate hole and screw the bracket in place.

Remove colortrac smartlf cx40 5 x M5 Pan Head Screws holding the end cover to the scanner. Re-insert the motor cog and tighten colortrac smartlf cx40 2 x grub screws. Check Colortrac colortrac smartlf cx40 and scanner drivers are installed correctly.

Move the extrusions until they are holding the mounting bracket firmly in place, with no free movement, but still able to freely remove the CIS mounting bracket again.

Take the 2 minute SingleSensor Challenge to see which imaging technology is the best-fit for your originals and application requirements, be they CAD, GIS, graphics, blueprints or photos. Completely remove the lid cover to reveal the inner cover plate. Disconnect the sensor cable from the front paper sensor to prevent it from being damaged when the roller is removed.

Canon Europe twitter instagram linkedin youtube.

colortrac smartlf cx40 Fine smartlt down the image can be either dirt or a scratches on the glass or dirt being picked up from the paper tray and dragged through. Drivers Software Firmware Utilities Loading Pull the front roller and other bear from the locating colortrac smartlf cx40 in Right Hand end cast, and being careful of the front sensor cable. Re-fit the 4 x M4 nuts to fasten motor in place making sure the washers are in place behind the nuts.

Below is a listing of our top FAQ’s. Third Party Certified third party software supplied by independent software vendors who have integrated dedicated SmartLF large format scanner support into their applications using the Colortrac Software Colortrac smartlf cx40 Kit SDK.

Scroll down to easily select items to add to your shopping cart for a faster, easier checkout.

Colortrac – Canon Europe

Comments to this Manuals Your Name. Items in search results. Replace the sensor and locate the locating pin of colortrac smartlf cx40 sensor into the bracket before re-fitting the screw. Page 48 of Use the following 2 tables to analyse any faulty scanners.

Check for free movement when bracket screwed in place. CopySmart can be ICC colour calibrated Profiled to any paper and ink by the customer in minutes colottrac the supplied IT8 target and in-built calibration Wizard. Product Chooser Which scanner is right for me? This on-line colortrac smartlf cx40 is a tool to help you find the right imaging technology for scanning your Large Format documents.